Gate drags and the operator strains
A dropped hinge or a settled post, not the motor. Fixing the gate first is what stops the operator burning out, and it is the cheaper of the two.
Grounds & Exterior1,682 businesses licensed for it
Fencing and gate repair
Fencing is a security boundary before it is a boundary marker, and a gate that will not close is an insurance conversation. Work covers repairing and replacing damaged panels and posts, chain link and security fencing, vehicle and pedestrian gates, gate operators and access hardware, and bollards and barriers protecting a building or a storage yard. Powered gates fail differently from fences: the fault is usually the operator, the safety loop or the sensors rather than the metalwork.
Enter your ZIP to see the businesses listed for this trade nearest to your site, with their phone numbers.
- Free to searchno account, nothing to submit
- Public registersevery listing names its source
- License numberswhere the state publishes one
- Directyou call the business yourself
- Our estimate
- $250-$9,000
- Time on site
- 2-20 hrs
- Fault patterns covered
- 2
- Licensed for this trade itself
- 1,682
What fencing and gate repair costs
Most of these jobs land near $750. The full spread runs $250 to $9,000, and the gap between those two ends is diagnosis against replacement rather than one business being dearer than another.
What moves it: how much of the job is parts, whether the fault is found in the first hour or the third, access to the equipment, and the hour of the day you call. We never speak to the businesses listed here, so there is no rate card behind any of this. It is our own band for the category, and there is no regional index: the figure does not change with your metro.
| How soon you need it | Typical | Range |
|---|---|---|
| Scheduled visitBooked in advance, no urgency multiplier applied | $750 | $250 to $9,000 |
| Same dayOur band multiplied by 1.12 | $840 | $280 to $10,080 |
| Emergency calloutOur band multiplied by 1.35 | $1,015 | $340 to $12,150 |
Our estimate from national cost bands, not a quote from any business. Every row is the same band with the urgency multiplier the site applies everywhere else, so this table can never contradict the headline number. Ask for a written price before the work starts.
Who is licensed to do this work
In California the classification that squarely covers this is C-13 fencing, and the register says who holds it. Every listing on this site shows the classification, the license number and the date we read it, with a link back to the register entry so you can check it against the state rather than against us.
Overlapping classifications exist and are labeled as overlapping rather than as a match: C-23 ornamental metal. A general building contractor may hold the job and subcontract the trade, which is a real answer and a different one, so the card says which of the two you are looking at.
One thing worth being plain about: CSLB classifications do not distinguish commercial work from residential. There is no separate commercial license to hold and no register field that would prove one. That is why this page describes the equipment rather than the contractor, and why nothing here says a business has been checked out. We read a public record on a stated date. That is the whole claim.
Before you pay for a callout
Two minutes of checks that sometimes end the problem
We would rather you did not need a callout at all. These are the checks that end the most calls for this fault.
Try a quick fix first
Some issues resolve without a truck roll. Two minutes now can save the callout.
- 1
Secure the gap temporarily and photograph it the day it happens. If it was a vehicle strike, the photograph and the police report is how you recover the cost.
- 2
For a powered gate, check the safety loop and the photo eyes before assuming the operator failed. A blocked or misaligned safety device stops the gate deliberately.
- 3
Measure the run and count the panels. Fencing is priced by the linear foot and a measurement is what makes prices comparable.
- 4
Check the boundary before replacing a shared fence. Rebuilding a neighbor's fence at your own cost is a common and irreversible mistake.
What the visit actually includes
- Removal and disposal of the damaged section
- New posts set to the correct depth for the fence type
- Panel, mesh or rail replacement to match
- Gate alignment, hinge and latch adjustment
- Operator, safety loop and sensor testing on powered gates
Diagnosis
How fencing faults usually present
Written from how these faults actually present on a working premises, not from a manual.
Posts lean after every wet season
Footings set too shallow for the soil. Replacing panels onto the same posts repeats the failure, so the posts are the actual job.
Listed for this trade
Businesses listed for fencing
Read from public license registers, so there is no ranking here and no distance: this page has no location to measure from. Enter your ZIP to sort by who is nearest to your site.
By location
Fencing and gate repair near you
Local pages show which businesses are listed for that metro, how far out they sit, and the local conditions that drive demand.
Counted from the businesses we have imported for each metro center inside a 25 mile radius, and counting only those whose own license classification names this trade. General contractors licensed widely enough to take it on and subcontract it are excluded here, and still appear in a search. A metro reads “none yet” until we load a register that covers this trade there.
All coverage areasQuestions owners ask
Fencing FAQs
Short, specific answers. If yours is not here, ask the business you call before you agree to the visit.
What license is this?
C-13 fencing in California, with D-28 doors, gates and activating devices for powered gates. Both are shown on the listings here where a business holds them.
Do I need a permit for a fence?
Repairs generally no. New fencing above a certain height, or anything in a front setback, usually does need one from your city, and the height limit varies by zone.
Can a powered gate be repaired same day?
Operator faults and sensors often yes. Anything needing a control board or a motor usually means a part on order, so ask about a manual release so you can still use the gate meanwhile.
Related work
Often booked in the same visit
Batching jobs into one mobilization is the cheapest way to buy this kind of work.
Tree serviceOverhanging limbs, storm damage, roots lifting paving and stump removal.from $300Parking lotPotholes, cracking, failed seal coat, faded striping, curbs and drainage.from $400Walk-in coolerCooler not holding temperature, iced coils, failed compressors and door seals.from $260Water heaterNo hot water, lukewarm supply, leaking tanks, pilot faults and tankless error codes.from $220
Grounds & Exterior
Everything else in grounds & exterior
Read next
How to check a California contractor license before you hire
Three minutes on the state's own lookup, what the result does and does not prove, and the two questions to ask on the phone.
7 min read
Walk-in cooler not getting cold: what to check first
Five checks that take ten minutes, plus the three readings a refrigeration tech needs before loading the truck.
7 min read
The two rooftop HVAC visits a year that pay for themselves
A spring cooling check and a fall heating check cost $340 to $700, and they are what stand between you and a $9,000 unit replacement.
6 min read
Ready when you are
Need fencing sorted?
Search your ZIP to see the businesses listed for this trade nearest to your site, with the license numbers and phone numbers we hold, then call them yourself.
- Cost to search
- Free
- Account needed
- None
- Who you call
- The business